Guangdong Juyao Intelligent Technology Co., Ltd. · Laser Software & Process R&D
23°07′N 113°15′E · GUANGZHOU · PURE STATIC MONOGRAPH
02 // LITERATURE & NOTES

Paper Index & Research Notes

Bar charts of joint tensile strength versus process parameters (Fig. 5 of Li et al., Materials 2026, CC BY 4.0; resized only, white padding added to fit 16:9): (a) ring powers of 800, 1000, 1200 and 1400 W give 270.5, 244.1, 172.9 and 117.4 MPa; (b) scanning frequencies of 100, 200, 300 and 400 Hz give 273.4, 281.2, 172.9 and 106.5 MPa — strength falls off a cliff beyond the sweet spot
Material & Process2026-11-16· 9 min read

Adjustable-ring-mode scanning laser welding of TA1 titanium to 304 stainless steel: joints reach 93.7% of the filler strength at 800–1000 W ring power — then fall off a cliff

Butt-welding 0.5 mm TA1 titanium to 304 stainless steel with a 1.2 mm AZ61S magnesium filler wire: at 800–1000 W ring power or 100–200 Hz scanning frequency, every joint averaged over 80% of the filler strength, peaking at 281.2 MPa; at 1400 W ring power the strength fell to 117.4 MPa, and at 400 Hz scanning frequency to 106.5 MPa. The good process is not “bigger” — it is “just right”.

Scanning electron micrographs of femtosecond laser–textured stainless steel (six panels): top row linear polarization (a) 17 mW, (b) 30 mW, (c) 45 mW; bottom row circular polarization (d) 17 mW, (e) 30 mW, (f) 45 mW; each panel combines a 5 μm low-magnification view with a 1 μm magnified inset — directional ripples under linear polarization, isotropic fine texture under circular polarization (Fig. 2 of Ji et al., Molecules 2026, CC BY 4.0; resized only, white padding added to fit 16:9)
Material & Process2026-11-09· 9 min read

Polarization-controlled femtosecond laser texturing of stainless steel: linear-polarized LIPSS cut E. coli adhesion to 4.8% while the contact angle barely moves

One 500 fs laser, one AISI 301 stainless steel plate, only the polarization state changed: at 30 mW, linear polarization cut bacterial adhesion to 0.0482 times the untreated surface, circular polarization to 0.1393 times — while all six textures sat in a narrow 32.6–36.9° contact-angle band. Antifouling is decided by stripe directionality, not by wettability.

Microscope image of a single femtosecond-laser groove in aluminium foil: the dark groove flanked by a discoloration band, annotated with groove width and HAZ proxy width, 100 μm scale bar; machined at 10 W and 80 mm/s, measured groove width 71 μm and HAZ proxy width 120 μm (Fig. 2 of Tański et al., Materials 2026, CC BY 4.0; resized only)
Material & Process2026-11-02· 9 min read

Teaching a neural network to predict femtosecond groove geometry from 100 experiments: test R ≈ 0.95 — but the HAZ is only an optical proxy

Two inputs, two outputs, two hidden layers (10 + 5 neurons): predicting groove width and discoloration-band width together across 1–10 W and 10–100 mm/s, with 11–15% errors — valid as interpolation inside that parameter space only.

Three-stage mechanism of femtosecond-laser sapphire/TC4 welding: heating (fs, nonlinear absorption, electron–phonon coupling), melting (ps, plasma-induced pressure, melt infiltration), rapid solidification (ns–μs, metallurgical bonding, interfacial compositional transition zone) (adapted from Fig. 7 of Zhao et al., Materials 2026, CC BY 4.0)
Material & Process2026-10-29· 9 min read

Femtosecond laser welding of sapphire to TC4: 51.55 MPa shear strength at 12.4 W, and why the wavy interface matters

Direct welding of a transparent ceramic to titanium alloy in ambient air: a 2.55–5.72 μm transition zone, and a strength peak that is not at the highest power.

Femtosecond-laser copper micropatterning: ink components, absorption spectrum, four-step process and copper-microwire morphology (adapted from Fig. 1 of Xue et al., Opto-Electronic Manufacturing 2026, CC BY 4.0)
Material & Process2026-10-16· 8 min read

Femtosecond laser writing of copper micropatterns: sub-10 μm lines at 9.34 μΩ·cm via a metal–organic ink

Dual-ligand ink plus an 80 °C pre-bake: tackling disordered grain growth and solvent micro-explosions at once.

Conceptual illustration of an ultra-short-pulse laser focused through glass onto the glass–metal interface to form a weld; not a measured experimental image
Material & Process2026-10-03· 8 min read

Ultra-short-pulse welding of glass to metal: shear strength above 50 MPa, where the weld stops being the weak link

Pinning energy at the interface: 3-ps bursts at 500 kHz heat accumulation weld at 10 mm/s and 57.7 MPa.

Conceptual illustration of a GHz-burst pulse train ablating a gold target through water; not a measured experimental image
Material & Process2026-10-01· 7 min read

GHz-burst ablation: bringing gold ablation efficiency in water toward the in-air limit

Temporal shaping as an independent process parameter: energy must arrive within the ~2 ns cavitation-shielding window.

Concept illustration of overlapping scan textures on steel and brass; not a measured specimen
Material & Process2026-09-22· 7 min read

Nanosecond laser metal engraving: scan overlap tradeoffs between removal rate and surface quality

Examining pulse overlap, particulate shielding, and quality estimator boundaries based on AISI 316L and CuZn37 experiments.

Conceptual illustration of a femtosecond pulse focused onto an ultrathin gold film on glass; not a measured experimental image
Materials & Process2026-09-18· 5 min read

How gold and nickel films change the femtosecond ablation threshold of glass

Single-pulse measurements, interfacial energy transfer, and the tests still needed for continuous processing.

Abstract study of continuous imagery, discrete marks, and tool paths
Computational Engraving2026-09-06· 8 min read

Halftone error diffusion: from image discretization to laser output states

Discretization with Neugebauer models and the additional calibration required for laser sources and materials.

Abstract study of laser energy input, scan paths, and material response
Material & Process2026-09-06· 9 min read

PMMA laser engraving: scan gap and multi-objective parameter optimization

How power, speed, and scan gap jointly affect energy use, throughput, and material removal.