Guangdong Juyao Intelligent Technology Co., Ltd. · Laser Software & Process R&D
23°07′N 113°15′E · GUANGZHOU · PURE STATIC MONOGRAPH
← Back to research
Material & Process2026-11-09· 9 min read

Polarization-controlled femtosecond laser texturing of stainless steel: linear-polarized LIPSS cut E. coli adhesion to 4.8% while the contact angle barely moves

One 500 fs laser, one AISI 301 stainless steel plate, only the polarization state changed: at 30 mW, linear polarization cut bacterial adhesion to 0.0482 times the untreated surface, circular polarization to 0.1393 times — while all six textures sat in a narrow 32.6–36.9° contact-angle band. Antifouling is decided by stripe directionality, not by wettability.

Scanning electron micrographs of femtosecond laser–textured stainless steel (six panels): top row linear polarization (a) 17 mW, (b) 30 mW, (c) 45 mW; bottom row circular polarization (d) 17 mW, (e) 30 mW, (f) 45 mW; each panel combines a 5 μm low-magnification view with a 1 μm magnified inset — directional ripples under linear polarization, isotropic fine texture under circular polarization (Fig. 2 of Ji et al., Molecules 2026, CC BY 4.0; resized only, white padding added to fit 16:9)
COVERScanning electron micrographs of femtosecond laser–textured stainless steel (six panels): top row linear polarization (a) 17 mW, (b) 30 mW, (c) 45 mW; bottom row circular polarization (d) 17 mW, (e) 30 mW, (f) 45 mW; each panel combines a 5 μm low-magnification view with a 1 μm magnified inset — directional ripples under linear polarization, isotropic fine texture under circular polarization (Fig. 2 of Ji et al., Molecules 2026, CC BY 4.0; resized only, white padding added to fit 16:9)
CORE RESEARCH QUESTION

Core question: by changing only the polarization state of a femtosecond laser — linear or circular — can bacterial adhesion on stainless steel be changed substantially without changing the surface wettability?

ABSTRACT

Ji and colleagues (Kongju National University, Kyungpook National University, Kumoh National Institute of Technology, Lawrence Berkeley National Laboratory) used a 500 fs, 1030 nm, 100 kHz laser to write laser-induced periodic surface structures (LIPSS) on 0.5 mm thick AISI 301 stainless steel: a spot of about 16 μm, scan speed 5 mm/s, line spacing 2 μm, powers of 17/30/45 mW, with linear and circular polarization compared. Linear polarization produced directional, anisotropic ripples that evolved into coarser hierarchical textures as power rose; circular polarization gave isotropic, finely packed morphologies, a symmetry difference confirmed by two-dimensional Fourier analysis. Static water contact angles for all six textures fell in 32.6–36.9° (58.8° untreated), so wettability barely differed — yet a 24 h static Escherichia coli adhesion test showed linear-polarized surfaces at 0.0482–0.1179 times the untreated adhesion and circular-polarized surfaces at 0.1393–0.2442 times, with 30 mW linear polarization best (0.0482×, about a 95% reduction). This note checks the processing parameters, the morphology evolution, the wettability and adhesion data, reconstructs the “wettability decoupled, directionality dominant” conclusion, and states where that conclusion stops applying. Cover: Fig. 2 of the paper (CC BY 4.0, resized only).

01 / Breaking an intuition first: more hydrophilic does not mean more antifouling

Stainless steel is the default material for food, medical and marine equipment, but its naturally high surface energy invites bacterial colonization and then biofilm. The usual countermeasures come in two kinds: coat it with a low-surface-energy or hydrating polymer, or copy shark skin and mollusk shells with biomimetic texturing. Coatings wear, delaminate and need reapplication; mechanical roughening lacks precision and leaves random micro-defects that can themselves become bacterial anchor points. This paper takes a third route: no coating at all, just a femtosecond laser writing micro- and nanostructures directly into the bulk — the structure is part of the substrate, so there is nothing to peel off.

What is really worth attention here is not “laser texturing can be antifouling” but that the paper separates two variables long treated as one. Many earlier studies attributed antifouling to contact angle: the more hydrophobic or hydrophilic the surface, the harder it is for bacteria to attach. But contact angle is a macroscopic average, and two very different topographies can measure the same angle. This paper builds exactly that control group: six textures — linear polarization at three powers and circular polarization at three powers — all with static water contact angles squeezed into a narrow 32.6–36.9° band (58.8° untreated), nearly identical wettability, while bacterial adhesion differs by a factor of two to five. Same wettability, different antifouling: what decides attachment is not “how wet the surface is” but “what the surface looks like”.

That decoupling is the methodological highlight of the paper. For process researchers it carries a warning: texture optimization that reports only contact angle can go astray — the angle works as a cheap process-monitoring metric, but not as a proxy for antifouling performance. What actually matters is the spatial organization and directionality of the micro- and nanotopography, and that is precisely what laser parameters can control directly.

02 / The experiment: one laser, only the polarization state changed

The material was 0.5 mm thick AISI 301 stainless steel (Goodfellow). The laser was an Amplitude s-Pulse system: 500 fs, 1030 nm, 100 kHz, focused through a 5× near-infrared objective to a spot of about 16 μm. Power was tuned continuously with a half-wave plate plus a polarizing beam splitter, and a quarter-wave plate switched between linear and circular polarization without changing other beam properties; a white-light co-illumination imaging system monitored the processing zone in real time. Texturing used raster scanning at 5 mm/s with a 2 μm line spacing and no assist gas, at three powers: 17, 30 and 45 mW.

The clean variable control is the basis of this paper’s credibility: one laser, one material, one scanning recipe, with polarization state and power as the only systematic changes. Table 1 lists pulse overlap, scan count and average fluence per condition, so the processing is reproducible. One caveat: processing ran in ambient air, and the authors expect surface oxidation on the treated surfaces — the oxide layer’s composition and thickness were not quantified here, so “no chemical additive” should be read as no added coating or biocide, not as no change in surface chemistry at all.

The antifouling test used Escherichia coli: cultured in LB broth at 37 °C for 16 h, centrifuged and resuspended in PBS, with each substrate fully immersed in the bacterial suspension and incubated statically at 37 °C for 24 h — a standard endpoint for static anti-adhesion and early-biofilm assessment, a single-time-point snapshot of attachment. After incubation the samples were gently rinsed with PBS to remove loosely attached cells, stained with a LIVE/DEAD kit, imaged by fluorescence microscopy and quantified with ImageJ, normalized to plain stainless steel as the reference (n = 3). The single-organism design was deliberate: it minimizes biological variability and isolates the effect of surface geometry.

03 / Morphology: linear polarization lines up ripples, circular polarization grows dots

Scanning electron microscopy (Fig. 2 of the paper, the cover of this note) shows the role of polarization most clearly. Under linear polarization at 17 mW the surface carries well-defined, oriented ripple structures — classic laser-induced periodic surface structures (LIPSS), arising from interference between the incident beam and surface-scattered waves; at 30 mW and 45 mW the ripples blur and the morphology transitions toward more irregular, coarser hierarchical textures, as increased energy deposition drives more material removal plus local melting and re-solidification. Circular polarization is entirely different: even at 17 mW the surface is a fine micro- and nanostructure with weak directionality, evolving at higher powers into densely packed, isotropic textures with no preferred orientation.

The authors do not stop at reading images by eye: they quantify anisotropy with two-dimensional fast Fourier transform (2D FFT) analysis. The linear-polarized surface gives a directionally elongated FFT map, with sharp spatial-frequency peaks only along the horizontal axis at about ±0.85–0.95 μm⁻¹ (period Λ about 1.1–1.2 μm) and no comparable feature on the vertical axis; the circular-polarized surface gives a near-rotationally symmetric FFT map, with horizontal and vertical profiles nearly overlapping and only broad, low peaks near ±1.5–1.6 μm⁻¹ (Λ about 0.6–0.7 μm). In one sentence: linear polarization gives “periodicity with a direction”, circular polarization gives “uniformity without one”.

The division of labour between the two knobs is therefore clear: polarization sets the symmetry and directionality of the morphology, while power mainly governs how much material is removed and how coarse the texture becomes. Together they form a tunable morphology space — and that is the physical origin of the antifouling differences that follow.

04 / Results: 30 mW linear polarization is best, adhesion 0.0482 times

The headline result first. Relative bacterial adhesion (untreated surface normalized to 1): linear polarization gave 0.0482–0.1179 across its three powers, circular polarization 0.1393–0.2442. The best condition was linear polarization at 30 mW, at 0.0482 times — about a 95% reduction versus untreated steel; circular polarization at the same power gave 0.1393 times. At low power (17 mW) linear gave 0.1179 and circular 0.2442; at high power (45 mW) both gave 0.0701. In other words, the polarization contrast is largest at 30 mW and converges when power is too high — the authors’ reading is that too little power forms the pattern incompletely, while too much power over-modifies the surface, and larger, more irregular features offer bacteria more favourable attachment sites.

SEM images of the adhered bacteria (Fig. 6 of the paper) agree with the numbers: the untreated surface is densely covered with rod-shaped E. coli; the circular-polarized 30 mW surface shows sparse cells with little clustering; the linear-polarized 30 mW surface retains only a few isolated cells. The proposed mechanism is geometric mismatch: anisotropic, linearly aligned LIPSS do not fit the rod shape of E. coli, restricting bacterial orientation and effective contact area and thereby hindering stable adhesion, while the isotropic protrusions of circular polarization impose no such orientational constraint. This is consistent with prior reports that bacterial attachment depends strongly on contact geometry and surface topography.

The word “antibacterial” needs precise wording: what the paper measures is adhesion suppression (antifouling / anti-adhesion), not a kill rate. LIVE/DEAD staining was used to assess the adhered bacteria, and the paper reports no killing percentage — so “adhesion down to 4.8%” must not be restated as “95% of bacteria killed”. Likewise, a 24 h static incubation is a snapshot of early attachment, not a long-term biofilm growth curve, and single-strain results do not transfer directly to mixed-species communities or real service environments, a limit the authors state explicitly.

05 / Lessons for process software — and the boundaries

Three lessons carry directly into laser-processing software design. First, polarization state belongs in the parameter space as a first-class process parameter: it changes no energy input yet switches the symmetry of the morphology — here, switching polarization changed adhesion by a factor of two to three, comparable to changing the power level. A parameter recommender that tunes power, speed and hatch spacing but not polarization is missing a whole dimension of optimization freedom; for functional-surface applications (antifouling, drag reduction, wettability control), polarization deserves a place in the process window alongside power. Second, evaluation metrics must align with function: since contact angle cannot distinguish good antifouling from bad, a “surface quality” score in software should not rest on wettability alone but should bring in morphology descriptors — FFT anisotropy, period and orientation, for example — and tie them to real functional tests (adhesion, friction, corrosion). Third, “coating-free and monolithic” is a durability selling point but also a verification duty: laser textures cannot delaminate, yet their wear resistance, corrosion resistance and long-service performance still need independent testing and cannot be derived from “formed in one piece” alone.

Boundary statement (consistent with the paper; please preserve it when citing). Licence and version: the paper is open access under CC BY 4.0; this note is an original interpretation with short quotations and does not reproduce the paper’s data tables; the cover is Fig. 2 of the paper, resized only (white padding added to fit 16:9), with source and licence in the caption. Experimental boundaries: AISI 301 stainless steel (0.5 mm) only, one 1030 nm / 500 fs / 100 kHz laser system only, and only inside the 17–45 mW window at 5 mm/s with a 2 μm line spacing; processed in air, with surface oxidation not quantified. Measurement boundaries: contact angles are static sessile-drop measurements (n = 3); adhesion is a relative value from a 24 h static incubation with a single strain (E. coli) at a single time point, reflecting adhesion suppression rather than a kill rate; mixed-species communities, flow conditions, long-term biofilm and durability were not tested in this study. Statistical boundaries: n = 3 per group, with relative adhesion normalized to the untreated surface; “best at 30 mW” is the best among the three tested powers, and finer power steps between them were not scanned. JUYAO has not replicated this on its own equipment. This is a research interpretation, not a process-recipe commitment.

PRIMARY SOURCE DOSSIER

Paper Title
Polarization-Controlled Femtosecond Laser Texturing Enables Robust Antifouling Stainless Steel Surfaces
Authors
Eunyeop Ji, Daesik Ko, Chan Hyeon Yang, Vassilia Zorba, Jung Hwan Park, Kyueui Lee, Minok Park
Journal
Molecules, 2026, Vol. 31, Issue 3, 480
Published
2026-01-29
DOI
10.3390/molecules31030480
Licence
Creative Commons Attribution 4.0 International (CC BY 4.0)
Original URL
Open original paper ↗