Guangdong Juyao Intelligent Technology Co., Ltd. · Laser Software & Process R&D
23°07′N 113°15′E · GUANGZHOU · PURE STATIC MONOGRAPH
← Back to news
Research Watch2026.11.09· 4 min read

Research Watch: A femtosecond laser directly figures and finishes freeform optics — 1.0 nm RMS figure error on borosilicate glass

Freeform surfaces let optical designers control light with fewer elements and tighter packages — AR/VR headsets, space telescopes, headlights and medical instruments all want them; the hard part is making them. The conventional route figures a surface first and polishes it afterwards: two steps, two alignments. The RIT team’s answer is to let a femtosecond laser do both at once.

Photograph from the RIT laboratory: Professor Jie Qiao (left, in red) with Ph.D. student Muhammad Akif Qadeer beside the femtosecond laser fabrication setup, with the laser processing system on an optical table to the right
COVERImage: RIT (photograph by Liam Myerow/RIT).
EXECUTIVE SUMMARY

On 9 November, the Rochester Institute of Technology (RIT) reported that Professor Jie Qiao’s team has used a femtosecond laser to directly figure and finish freeform optical surfaces, shaping and polishing in a single step with no separate polishing stage. The underlying paper was published in Optics Express on 21 July 2026 (open access): an experimentally characterised and numerically optimised point influence function models the surface response, iterative scan-path deconvolution generates the fabrication trajectories, and Zernike-polynomial freeform surfaces on borosilicate glass reach a root-mean-squared figure error of 1.0 nm.

01 / The method: model what one laser spot removes, then work backwards to the scan path

The core of this work is not “how powerful the laser is” but “how predictable the removal is”. The team first characterised the point influence function of the femtosecond laser on glass — the material-removal profile at a single spot — then optimised it numerically to predict the surface shape after a full pass, and used iterative scan-path deconvolution to compute the trajectory the spot must follow to reach the target figure. The target figures are defined by Zernike polynomials, the standard language for describing freeform surfaces.

The result is deterministic: freeform surfaces on borosilicate glass with a root-mean-squared figure error of 1.0 nm, and predicted surface profiles that agree closely with the measured ones. What does 1.0 nm mean? Visible light spans roughly 400–700 nm, so this error is about one four-hundredth of a wavelength — for a precision optic, that is “finished as fabricated”, and it is what lets the team claim no separate polishing step is needed.

02 / The background: a decade-old idea, now ready for industrial use

The idea began more than a decade ago, when Qiao first proposed using ultrafast lasers to fabricate freeform optics directly; her group then spent ten years studying how ultrashort pulses interact with materials, building models and developing the process before reaching this demonstration. RIT notes that the femtosecond-laser fabrication technology is patented and licensed to industry and continues to draw interest from companies — for laser-processing readers, that matters more than the paper alone: the route has moved past “it works in the laboratory” and is being tested by industry.

The same announcement notes that the Laser Institute, the international professional society for laser applications and safety, elected Qiao a Fellow in the fall of 2026 — its highest membership grade — recognising her pioneering work in ultrafast-laser precision fabrication of freeform optics. Qiao is also an Optica Fellow, served as general chair of CLEO in 2024 and 2025, and will serve as general chair of ICALEO 2027.

03 / Significance and limits: for laser-processing software, the lesson is in the path inversion

For JUYAO’s readers, the lesson is not only that “a femtosecond laser can polish glass” but the method: characterise the spot’s removal as a computable point influence function, then invert it by deconvolution to obtain the scan path — the same class of problem as deriving scan spacing and energy from a target grey level in laser engraving. Only when the removal process can be modelled to nanometre accuracy can software promise “figured in one pass” as a process.

The limits need stating too: the demonstration is on borosilicate glass, and 1.0 nm is the result for that material and those figures — a different material, figure or size needs re-characterisation; the paper does not give a complete mapping of processing speed against figure size, so throughput for large freeform surfaces remains open. Read it as a proof of concept for deterministic femtosecond-laser fabrication of freeform optics that has reached industry’s door, rather than as a ready production process.

PRIMARY REFERENCES & LINKS

  • RIT students and their professor turn laser research vision into reality
    RIT · 9 November 2026

    RIT announcement verified: published 9 November 2026; the simultaneous figuring and finishing of freeform surfaces with a femtosecond laser, the patented technology licensed to industry, Qiao’s election as a Laser Institute Fellow in the fall of 2026, and the NSF STELLAR Engine’s $15 million collaboration all come from this announcement.

    Open source link ↗
  • Deterministic fabrication of freeform optics using direct femtosecond laser figuring
    Optics Express · 21 July 2026 · Open Access

    Original paper verified: Qadeer, Sanderson and Qiao, Optics Express, vol. 34, no. 15, p. 28177, DOI 10.1364/oe.605638, open access (Optica OA License v2); the point influence function, iterative scan-path deconvolution, Zernike-polynomial figures, borosilicate glass and 1.0 nm RMS figure error all come from the paper’s abstract and publication record.

    Open source link ↗